Exactly How To Install A Tub (For Beginners).
Exactly How To Install A Tub (For Beginners).
Blog Article
Just how do you feel about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't specifically rocket science, yet it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging job. If the old tub is easily obtainable, the project can move speedily; if you need to open up a wall to eliminate the old bathtub as well as place the brand-new tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will require an assistant to leave the old bathtub and set in the brand-new one. Ensure you have certified yourself for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is far better to think about utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube connections.
This write-up will assist you set up a brand-new bathtub in your shower room if you have actually currently bought a new tub and don't need to transform the setup of your previous supply of water pipelines.
Your devices and also product checklist ought to comprise the following:
Planning for the Installation
Firstly, the supporting frame supplied with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath should currently prepare to be suited its final position.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of removing the existing taps can be fairly troublesome due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Making use of the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the tub till the level checks out degree.
To install faucets, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the water system and also examine all joints and new pipework for leaks as well as tighten them if essential. Load the bath tub and additionally examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub should wait until the bathtub has been used a minimum of once as this will certainly resolve it right into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washing machines remain in location in between the faucet as well as the sink. Secure the tap in place with the producer offered backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The former type should be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, creating the water to pass through the wall surface in between the bathroom and the tiling, causing problems with dampness and possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always load the bath tub with water before sealing, to permit the motion experienced when the tub is in usage. The sealer can crack rather early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently readily available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very involved in How to Install a Bathtub Yourself and I hope you enjoyed reading the new entry. Be sure to take the opportunity to distribute this blog post if you enjoyed it. I praise you for your time. Kindly come by our site back soon.
Browse Our Site Report this page